1、 November 26, 2013 New York Standard Approach for Estimating Energy Savings from Energy Efficiency Programs (Technical Resource Manual TRM) 1 RECORD OF REVISION Revision Number Issue Date Effective Date Range Measure Heading/Subsection of Tech Manual Change or Addition and Brief Description of Chang
2、e/Addition Location/Page in Tech Manual (October 15, 2010) 11-13-1 11/26/13 12/1/13-2/31/14 Dehumidifiers Energy Star Dehumidifier Revises savings estimates based on latest Energy Star criteria. Pg. 105 11-13-2 11/26/13 12/1/13-2/28/14 Water Heaters Water Heater, Indirect Water Heater, Heat Pump Wat
3、er Heater Adjusts conversion factor of Btu/gallon-0F and aligns compliance efficiencies for gas and electric water heaters with NYS Energy Conservation Construction Code Pgs. 79, 81, 82, 84, 87, 89, 91 11-13-3 11/26/13 12/1/13-2/28/14 Effective Full Load Hours (EFLH) for Heating and Cooling Heating
4、and Cooling Equivalent Full-Load Hours (Appendix G) Corrects labeling of “Office Building” category in EFLH cooling table to “Large Office Building” category; adds the category “Dormitory” to the EFLH heating table; consolidates the previously separated EFLH cooling values into one table. Pgs. 430-4
5、35 November 26, 2013 New York Standard Approach for Estimating Energy Savings from Energy Efficiency Programs (Technical Resource Manual TRM) 2 RECORD OF REVISION Revision Number Issue Date Effective Date Range Measure Heading/Subsection of Tech Manual Change or Addition and Brief Description of Cha
6、nge/Addition Location/Page in Tech Manual (October 15, 2010) 9-13-1 9/27/13 10/1/13-12/31/13 Primary Refrigerators Refrigerator Rebates N/A New Section 9-13-2 9/27/13 10/1/13-12/31/13 Refrigerators and Freezers Refrigerator and Freezer Recycling Pgs. 22-23 9-13-3 9/27/13 10/1/13-12/31/13 Weighting F
7、actors for Commercial Building Calculations (Appendix B) Weighting Factors for Commercial Building Calculations (Appendix B) Pg. 253 8-13-1 8/31/13 9/1/13 11/30/13 Furnaces and Steam Boilers Furnace and Boilers (Commercial): Corrects Record of Revision number 7-13-11 in two ways. 1) Minimum efficien
8、cy for gas furnaces less than 225 kBtu/hr is 78% AFUE or 80% thermal efficiency(Et). 2) Minimum efficiency for steam boilers with greater than 2,500 kBtu/hr capacity is 80% combustion efficiency( Ec). Pg. 137 8-13-2 8/31/13 9/1/13 11/30/13 Boilers (Residential) and Furnaces and Boilers (Commercial)
9、Boilers (Residential): Compliance Efficiency from which Incentives are Calculated Clarifies that the table containing the baseline efficiencies from which incentives are calculated is a recommendation by DPS and not policy. Furnaces and Boilers (Commercial): Compliance Efficiency from which Incentiv
10、es are Calculated Clarifies that the table containing the baseline efficiencies from which incentives are calculated is a recommendation by DPS and not policy. Pgs. 49 & 137 November 26, 2013 New York Standard Approach for Estimating Energy Savings from Energy Efficiency Programs (Technical Resource
11、 Manual TRM) 3 RECORD OF REVISION Revision Number Issue Date Effective Date Range Measure Heading/Subsection of Tech Manual Change or Addition and Brief Description of Change/Addition Location/Page in Tech Manual (October 15, 2010) 7-13-1 7/31/13 8/1/13-10/31/13 Building Type Descriptions Introducti
12、on: Adds a table listing each of the 27 building types with brief description. Adds new table in Introduction section 7-13-2 7/31/13 8/1/13-10/31/13 CFL CFL: Savings Estimation Approach Adds statement that permits usage of actual wattage data (of CFL) and manufacturers cut data sheet when known, in
13、place of deemed value in Appendix C. Adds method for replacing halogens. Pgs. 12, 107 7-13-3 7/31/13 8/1/13-10/31/13 Refrigerators Refrigerators Adds and describes 2 options that can be utilized to estimate energy savings due to refrigerator replacement. Description of the metering option is removed
14、. Also adds savings adjustment factors based on age and seal condition of refrigerator being replaced. Pgs. 16-17 7-13-4 7/31/13 8/1/13-10/31/13 Refrigerator/ Freezer Bounty Refrigerator and Freezer Recycling: Annual Energy and Summer Peak Demand Savings Replaces deemed peak kW savings factor with t
15、emperature adjustment and load shape factors. Pg. 23 7-13-5 7/31/13 8/1/13-10/31/13 Indirect Water Heater (Residential) Residential Indirect Water Heater: Method for Calculating Energy Savings Adds title of “Gallons per Day” Pg. 85 7-13-6 7/31/13 8/1/13-10/31/13 Indirect Water Heater (Residential) R
16、esidential Indirect Water Heater: Tank overall heat loss coefficient Heat loss coefficient (UA) default values added for typical water heater sizes; 40, 80 & 120 gallons. Pg. 86 7-13-7 7/31/13 8/1/13-10/31/13 Faucet Aerators Faucet Aerators: Summary of Variables and Data Sources Corrects transpositi
17、on of GPM usage in table. Pg. 95 November 26, 2013 New York Standard Approach for Estimating Energy Savings from Energy Efficiency Programs (Technical Resource Manual TRM) 4 RECORD OF REVISION Revision Number Issue Date Effective Date Range Measure Heading/Subsection of Tech Manual Change or Additio
18、n and Brief Description of Change/Addition Location/Page in Tech Manual (October 15, 2010) 7-13-8 7/31/13 8/1/13-10/31/13 Lighting (Commercial) Interior and Exterior Lighting: Method for Calculating Summer Peak Demand and Energy Savings Adds/defines baseline conditions for retrofits. Pgs. 109, 111 7
19、-13-9 7/31/13 8/1/13-10/31/13 Interior Lighting Controls Interior Lighting Controls Adds method and table to calculate full load hours using automatic controls. Pg. 113 7-13-10 7/31/13 8/1/13-10/31/13 Boilers and Furnaces (Commercial) Furnaces and Boilers: Method for Calculating Energy Savings Modif
20、ies text to define thermal efficiency and how it and combustion efficiency are used for larger boilers and furnaces. Pgs. 136-137 7-13-11 7/31/13 8/1/13-10/31/13 Boilers and Furnaces (Commercial) Furnaces and Boilers: Method for Calculating Energy Savings Addition to text defines minimum efficiencie
21、s for furnaces and boilers in accordance with New York State Energy Conservation Construction Code Pgs. 137-138 7-13-12 7/31/13 8/1/13-10/31/13 Variable Frequency Drives Variable Frequency Drives: Method for Calculating Summer Peak Demand and Energy Savings Corrects incorrect appendix reference (sho
22、uld be Appendix K.) Pg. 157 7-13-13 7/31/13 8/1/13-10/31/13 Indirect Water Heaters (Commercial) Indirect Water Heaters Method for Calculating Energy Savings Corrects definition of thermal efficiency and removes unused definitions. Pg. 165 November 26, 2013 New York Standard Approach for Estimating E
23、nergy Savings from Energy Efficiency Programs (Technical Resource Manual TRM) 5 RECORD OF REVISION Revision Number Issue Date Effective Date Range Measure Heading/Subsection of Tech Manual Change or Addition and Brief Description of Change/Addition Location/Page in Tech Manual (October 15, 2010) 7-1
24、3-14 7/31/13 8/1/13-10/31/13 Indirect Water Heaters (Commercial) Indirect Water Heaters Method for Calculating Energy Savings Copies table containing deemed values of water usage from “Water Heaters” section above into this section. Also Corrects UA values table by removing “base” so that resulting
25、table indicates UA values based on diameter and insulation. Pgs. 166-167 7-13-15 7/31/13 8/1/13-10/31/13 Pipe Insulation Pipe Insulation: Adds entirely new section covering savings in space heating and domestic hot water through installation of pipe insulation. N/A New Section 7-13-16 7/31/13 8/1/13
26、-10/31/13 Evaporator Fan Controls Evaporator Fan Controls: Savings Estimation Approach and Summary of Variables and Data Source Corrects mislabeled savings factor, Fcontrol and corrects formulae for calculating kWh and kW savings. Pgs. 175-176 7-13-17 7/31/13 8/1/13-10/31/13 ECMs ECMs for Refrigerat
27、ed Cases and Walk In Cooler Fans Corrected formula for kWh Pg. 185 7-13-18 7/31/13 8/1/13-10/31/13 Building Prototypes Appendix A: Refrigerated Warehouse Clarifies that the building model applies only to new construction. Appendix A, pg. 249 7-13-19 7/31/13 8/1/13-10/31/13 Minimum Outdoor Air Fracti
28、on Appendix A: Hotel: Defines term “PTAC” and adds “Minimum Outdoor Air Fraction to building characteristics listing; FYL only, term not used in calculation and applies only to portions of building covered by HVAC system. Appendix A, pg. 235 7-13-20 7/31/13 8/1/13-10/31/13 Building Prototypes INTROD
29、UCTION & Appendix A: Commercial Building Prototypes Clarifies what constitutes “other” and when it should be used. Pgs. 11, 218 respectively November 26, 2013 New York Standard Approach for Estimating Energy Savings from Energy Efficiency Programs (Technical Resource Manual TRM) 6 RECORD OF REVISION
30、 Revision Number Issue Date Effective Date Range Measure Heading/Subsection of Tech Manual Change or Addition and Brief Description of Change/Addition Location/Page in Tech Manual (October 15, 2010) 7-13-21 7/31/13 8/1/13-10/31/13 Building Prototypes Appendix A: Prototypical Building Descriptions Cl
31、arifies definition of “old”, “average”, and “new” vintage by eliminating gaps in range of year categories. Appendix A, pg. 209 7-13-22 7/31/13 8/1/13-10/31/13 Weighting Factors for Commercial Buildings Appendix B: Weighting Factors for Commercial Building Calculation Adds weighting factors for HVAC
32、interactive effects for 13 building types and “other.” N/A Adds new table after low-rise weighting factor table. 7-13-23 7/31/13 8/1/13-10/31/13 Lighting Appendix C: Standard Fixture Watts Adds additional fixtures throughout Appendix C. Throughout Appendix C, pgs. 254-288 7-13-24 7/31/13 8/1/13-10/3
33、1/13 Roof Insulation Appendix E: Roof Insulation Corrects mislabeled item in last NYC table; should read “Gas Heat, No AC.” Appendix E, pg. 319 7-13-25 7/31/13 8/1/13-10/31/13 Air Leakage Sealing and Opaque Shell Insulation Appendix E: Opaque Shell Measure Savings Adds statement at beginning of sect
34、ion that effective R values reflect the factors of compression and installation quality. Appendix E, pg. 297 7-13-26 7/31/13 8/1/13-10/31/13 Wall and Roof Insulation Appendix E: Adds missing R value column for Binghamton. Appendix E, pgs. 325-330 7-13-27 7/31/13 8/1/13-10/31/13 Page Header and R Val
35、ue Correction Appendix H: Residential Distribution System Efficiency in Cooling Mode (Attic Ducts) Corrects page headers which incorrectly identified this section as G. R value corrected in two pages to correctly list values as R-6. Appendix H, pgs. 437-438 7-13-28 7/31/13 8/1/13-10/31/13 Engine Blo
36、ck Heater Timer Engine Block Heater Timer Adds this agricultural measure. N/A-New Section 7-13-29 7/31/13 8/1/13-10/31/13 Indirect Residential Water Heaters Deemed value of 1 inch insulation if thickness of tank insulation not known. Pg. 98 November 26, 2013 New York Standard Approach for Estimating
37、 Energy Savings from Energy Efficiency Programs (Technical Resource Manual TRM) 7 RECORD OF REVISION Revision Number Issue Date Effective Date Range Measure Heading/Subsection of Tech Manual Change or Addition and Brief Description of Change/Addition Location/Page in Tech Manual (October 15, 2010) 7
38、-13-30 7/31/13 8/1/13-10/31/13 Commercial programmable setback thermostats (PSTs) Default value from table has been removed. Engineering judgment may be required if installing only PST. Pg. 151 7-13-31 7/31/13 8/1/13-10/31/13 Evaporator fan controls & ECM Motors in refrigerator cases & Walk-In Coole
39、r Fans Corrects formulae to derive kW value. (Volts x amps must be divided by 1000.) Pgs. 174, 185 7-13-32 7/31/13 8/1/13-10/31/13 Boilers & Furnaces Correction of error in formula. Pgs. 47, 77 7-13-33 7/31/13 8/1/13-10/31/13 Residential Indirect Water Heaters Missing unit conversion factor correcte
40、d. Pg. 83 7-13-34 7/31/13 8/1/13-10/31/13 Residential (& Commercial) Indirect Water Heaters Recovery efficiency used to determine UA now listed in residential section; for larger boilers UA is determined by using standby loss specification. Pgs. 85 & 165 7-13-35 7/31/13 8/1/13-10/31/13 Residential I
41、ndirect Water Heaters Removes reference to electric water heater as baseline unit. Pg. 85 7-13-36 7/31/13 8/1/13-10/31/13 Water heaters, residential and commercial Corrects inconsistent unit conversion factor of 100,000 BTUs/therm Pgs. 78, 159 7-13-37 7/31/13 8/1/13-10/31/13 EFLH for Room Air Condit
42、ioners Manual now lists most current, verified EFHL for Con Ed of 382 hours. Pgs. 76-77 7-13-38 7/31/13 8/1/13-10/31/13 Opaque Shell Insulation Identification of peak coincidence factor (CFs) corrected. Pg. 26 7-13-39 7/31/13 8/1/13-10/31/13 Chillers Transitions from use of Coefficient of Performanc
43、e (COP) to kW/ton for purpose of sizing chillers. Minimum efficiencies listed are least stringent allowed by NYS ECC and provide greater flexibility to PAs. Pg. 145 7-13-40 7/31/13 8/1/13-10/31/13 Commercial Indirect Water Heaters Deemed value of 1 inch insulation if thickness of tank insulation not
44、 known Pg. 98 November 26, 2013 New York Standard Approach for Estimating Energy Savings from Energy Efficiency Programs (Technical Resource Manual TRM) 8 RECORD OF REVISION Revision Number Issue Date Effective Date Range Measure Heading/Subsection of Tech Manual Change or Addition and Brief Descrip
45、tion of Change/Addition Location/Page in Tech Manual (October 15, 2010) 7-13-41 7/31/13 8/1/13-10/31/13 Refrigerators The inserted footnote describes how the retail rebate measure does not require a chapter, and its analysis can otherwise use materials in this chapter. Rebates at the retail level af
46、fect choice between new refrigerators, leaving no existing old one to be recycled or not Pg. 15 6-13-1 6/30/13 7/1/13 9/30/13 Water Heater (Residential) Method for Calculating Energy Savings Revises the inlet water temperature (T mains column) in the accompanying tables for New York City from 62.50
47、to 550 (F) AND Inserts row for inlet water temperature (T mains column) in accompanying tables for Long Island, to acknowledge difference of water source from NYC. Inlet water temperature for Long Island established at 62.50(F) Pg. 80 6-13-2 6/30/13 7/1/13 9/30/13 Indirect Water Heater (Residential)
48、 Same as above. Pg. 85 6-13-3 6/30/13 7/1/13 9/30/13 Heat Pump Water Heater (Residential) Same as above. Pg. 90 6-13-4 6/30/13 7/1/13 9/30/13 Low Flow Showerheads (Residential) Same as above. Pg. 93 6-13-5 6/30/13 7/1/13 9/30/13 Faucet Aerators (Residential) Same as above. Pg. 95 6-13-6 6/30/13 7/1/
49、13 9/30/13 Water Heaters (Commercial) Same as above. Pg. 161 6-13-7 6/30/13 7/1/13 9/30/13 Indirect Water Heater (Commercial) Same as above. Pg. 166 6-13-8 6/30/13 7/1/13 9/30/13 Low Flow Showerheads (Commercial) Same as above. Pg. 171 6-13-9 6/30/13 7/1/13-9/30/13 Faucet Aerators (Commercial) Same
50、as above. Pg. 173 3-13-1 3/14/13 3/14/13 Appendix O C&I Lighting Policy On DPS Website November 26, 2013 New York Standard Approach for Estimating Energy Savings from Energy Efficiency Programs (Technical Resource Manual TRM) 9 RECORD OF REVISION Revision Number Issue Date Effective Date Range Measu
