1、ASSEMBLY AND OPERATING INSTRUCTIONS GLIDER SOLOSpecifications:Length: 930mmWingspan: 1500mmWing Area: 26.5dm2Wing Loading: 27g/dm2Flying Weight: 715gPlease read carefully before use SOLO RTF.Remark: this glider has two horizontal tails: V-tail and T-tail.Safety Precautions: This electric R/C model p
2、lane is not a toy. Skill level is designed for the intermediate pilot with some flying and building experience. Children younger than 14 years old must use it accompanied by an adult. Please choose an open place to fly away from buildings and overhead power lines. Please always put safety first and
3、operate in a safe and reasonable manner.The battery must be fully charged before attempting to fly this model. Battery Charging:To charge the battery, connect the white lithium balance connector of the battery to your charger and connect the charger to a suitable 11.1v battery. The green charging li
4、ght will illuminate indicating that the battery is charging correctly. When the green light is no longer illuminated the battery is ready to use. Charging time will be approximately 2.5 hours, but this will vary depending upon the condition of the battery and the charge remaining in it at the time o
5、f charging.Important Safety Note:When charging the battery, it is important to keep battery and charger under observation and never to leave them unattended. Disconnect the battery from the charger when it has finished charging.Part No. Description1. Body2. Wing3. Horizontal tail (T-tail & V-tail)4.
6、 Fin5. Charger6. Li-Po Battery7. Transmitter8. PropellerAssembly Manua6Assembly Instructions:1. Connect the wing tube to each wing panel (Pic 01-02); and then assemble the wing panel to the fuselage. (Pic 03) （01） (02) (03)2. Apply glue（glue not included）to the control rods and stabilizer and follow
7、s the slot to fix to the fuselage; and remove any excess glue and hold in position until glue sets. (Pic 04-05)（04） （05）3. Apply glue to the control rods and vertical fin and follows the slot to fix to the stabilizer; remove any excess glue and hold in position until glue sets. (Pic 06-07) （06） （07）
8、4. Apply glue to the control rods, and follow the slot to fix to the wing; remove any excess glue, the servo in wing is factory-assembled. (Pic 08). Install the steel to the wing /rudder, the steel which connect the servo in wing. (Pic 09-10) (08) （09） （10）5. Install the steel to the vertical fin/ru
9、dder, the steel which connect the servo in fuselage is factory-assembled (Pic11). Install the steel to the stabilizer/rudder, the steel which connect the servo in fuselage is factory-assembled. (Pic 12) （11） （12） 6. Assemble the propeller in the right place and use fix with cross head screw provided
10、. (Pic 13-15) （13） （14） (15) Pic. 12 Pic. 12Pic. 14Pic. 12Pic. 147. Connect the speed controller to the receiver. (Pic 16) and adjust the airplane and make sure the Center of Gravity (CG) is as indicated in the following diagram.45mm (CG)the center of gravity（16）Final Adjustments and Switching On1.
11、Switch on the transmitter making sure that the throttle stick and throttle trim tab is in the throttle off position (fully down). Centralize all the other trim tabs.2. Insert the flight battery into the radio bay and connect the battery to the speed controller. You will hear three beeps meaning that
12、 all is working well.3. Check that the servos are centralized and make any minor adjustments to the servos and or control cables as necessary. The rudder and elevator surfaces should be centered after making these minor adjustments.4. Replace canopy attached decals using box illustration as a guide
13、and you are ready to fly.l Beginners should seek help and advice from an experienced person.l Choose an area large enough away from buildings, people, vehicles and overhead power lines. Always check that your batteries are fresh and charged. After switching on your transmitter and model check that there is no interference.l Do not fly in strong winds and choose a fairly calm day for your first flight.l Always disconnect your battery when not in use.l We hope you have enjoyed assembling this model.
